There are innumerable problems that can happen with any painted walls.
It may occur on newly newly colored surface or it can happen with time.
The ultimate technique to avoid these untoward painting problems is to know preventative steps which occur before applying a new color.
Below are usual coloring troubles and the corresponding tips on how to handle them.
One problem that usually happens is what we call the blocking.
It's when two colored surfaces are fastened together which is not the end result you want like sticking of the door to the jam.
This takes place because the color did not wholly dry prior to closing the door.
Another reason is the use of latex colored with inferior grade.
In addition to providing more time for drying, a better option is to use a color of higher quality or look for semi-gloss acrylic latex color.
More often than not, the grade of latex color is proportional to its cost.
The higher the grade, the more money you need to shell out.
Spending money on quality color is a lot better than spending for low grade paints plus the possibility of back job costs.
Have you seen a wall that appears to be overly glossy in some areas? That is what you call burnishing.
The cause of this is too much brushing or rubbing of the wall abrasively.
This doesn't happen on newly painted walls but it happens over time especially on areas with high traffic.
You will notice that when a fixture or any equipment is rubbed against a painted wall, there will be glossy areas.
The culprit for this is the use of flat paint without scrub resistance.
So for spots that needs frequent cleaning, the best way is to use a semi-gloss or gloss paint.
Cleaning walls painted with gloss paints can easily be done using soft cleaning material such as sponge.
Also when cleaning, always rinse the area with clean water.
There is also what we call sagging which happens right after applying the paint.
It's when the paint seems to droop giving an uneven depth of paint.
There are a number of reasons why this problem occurs.
It may be due to applying excessive paint or having a paint coat which is too thick.
When using a spray gun, application of paint with gun too close on the wall can also result to this problem.
Another reason which we can never change is the weather condition.
Too humid or too cold weather conditions can fasten sagging of paint.
Solution for this lies on the way the paint is applied.
During the process of painting, promptly reroll the brush when you see an uneven area.
At times when you feel it's too late and the paint has dried a bit, sand the uneven spot gently and apply an additional coat of paint.
To really avoid this problem, apply enough paint sufficient for that spot and not mound the paint on the wall.
Nobody wants those residential paint problems to happen.
If you wish to do your painting project rather than having a professional do it, take some time to read and study some basics of painting.
Preventive measure is always better than finding a solution for a given problem.
It may occur on newly newly colored surface or it can happen with time.
The ultimate technique to avoid these untoward painting problems is to know preventative steps which occur before applying a new color.
Below are usual coloring troubles and the corresponding tips on how to handle them.
One problem that usually happens is what we call the blocking.
It's when two colored surfaces are fastened together which is not the end result you want like sticking of the door to the jam.
This takes place because the color did not wholly dry prior to closing the door.
Another reason is the use of latex colored with inferior grade.
In addition to providing more time for drying, a better option is to use a color of higher quality or look for semi-gloss acrylic latex color.
More often than not, the grade of latex color is proportional to its cost.
The higher the grade, the more money you need to shell out.
Spending money on quality color is a lot better than spending for low grade paints plus the possibility of back job costs.
Have you seen a wall that appears to be overly glossy in some areas? That is what you call burnishing.
The cause of this is too much brushing or rubbing of the wall abrasively.
This doesn't happen on newly painted walls but it happens over time especially on areas with high traffic.
You will notice that when a fixture or any equipment is rubbed against a painted wall, there will be glossy areas.
The culprit for this is the use of flat paint without scrub resistance.
So for spots that needs frequent cleaning, the best way is to use a semi-gloss or gloss paint.
Cleaning walls painted with gloss paints can easily be done using soft cleaning material such as sponge.
Also when cleaning, always rinse the area with clean water.
There is also what we call sagging which happens right after applying the paint.
It's when the paint seems to droop giving an uneven depth of paint.
There are a number of reasons why this problem occurs.
It may be due to applying excessive paint or having a paint coat which is too thick.
When using a spray gun, application of paint with gun too close on the wall can also result to this problem.
Another reason which we can never change is the weather condition.
Too humid or too cold weather conditions can fasten sagging of paint.
Solution for this lies on the way the paint is applied.
During the process of painting, promptly reroll the brush when you see an uneven area.
At times when you feel it's too late and the paint has dried a bit, sand the uneven spot gently and apply an additional coat of paint.
To really avoid this problem, apply enough paint sufficient for that spot and not mound the paint on the wall.
Nobody wants those residential paint problems to happen.
If you wish to do your painting project rather than having a professional do it, take some time to read and study some basics of painting.
Preventive measure is always better than finding a solution for a given problem.
SHARE
