Repairing A Rotted Soffit
If you don't even know what a "soffit" IS, then chances are you're not the best candidate to do repairs on it! Many older houses naturally start rotting at the weakness points, one of them being the soffit – or the underside of an arch, stairwell, cornice or overhang. Often times even newer houses need their soffits replaces because squirrels and birds tend to nest in the eaves, gutters or outer wall space next to the attic. The soffit, typically made of soft plywood, hardwood, or soft panels of vinyl and aluminum, routinely comes into direct contact with rain water, ice and snow from the gutters. If your gutters have been displaced or if a shingle tears, the soffit will rot out over time. Atlanta painting contractors often specialize in solving this external problem for you, thus preventing more serious damage to the interior as well.
To replace the rotted soffit, you would need to pry off the shingle mold running along the top edge of the fascia board and yank out all the nails that held the rotting board in place. Next, replace the board with a pre-measured or trimmed piece of hardwood, vinyl or aluminum. Remove any decorative trim beneath the soffit and remove the rotted soffit. Note that this part of the process is usually rather disgusting, since you never know what kind of dirt, dust, bee nest, squirrel nest, or debris will come off. Now you should be able to see the frame clearly and ascertain where the water damage and decay started. You may need to rip out additional plywood sheathing and use your saw to take out the section of rotted rafter or roofing. You'll have to cut four or more inches from the decay, to account for stress fractures that may have left room for water to seep in. This is where the tools come in handy: you'll need a powder-actuated nail gun with a .22 caliber blank to nail in the new section.
You'll also be attaching a pressure-treated 1x4 or 1x6 onto the newly sawed rafter, fastening it with 2.5" galvanized screws going from the new into the old rafters. Now you can cut a new soffit from a 3/8-inch A/C plywood, first coating the front and back flat surfaces with an exterior primer and the edges with a wax emulsion sealer (like AnchorSeal) to protect from water damage. Apply sealer with a foam or bristle brush. Nail the soffit into place and replace the trim you've removed. Cut a new fascia board and replace it. (Warning: This requires careful measuring to get the right size!) Now prime all four surfaces of this board. Seal the end cuts and install it, then nail up the shingle molds along the fascia.
Sound like a LOT of work? IT IS! The process is extremely convoluted for anyone who isn't a skilled tradesman. What might take a novice several days could be done in an afternoon by an Marietta Georgia painting contractor. Therefore, you may want to track down a contractor to meet your needs. Not only will your home look totally renovated and newer, but more importantly, you will be protecting your home from premature aging as a result of water and rot damage.
If you don't even know what a "soffit" IS, then chances are you're not the best candidate to do repairs on it! Many older houses naturally start rotting at the weakness points, one of them being the soffit – or the underside of an arch, stairwell, cornice or overhang. Often times even newer houses need their soffits replaces because squirrels and birds tend to nest in the eaves, gutters or outer wall space next to the attic. The soffit, typically made of soft plywood, hardwood, or soft panels of vinyl and aluminum, routinely comes into direct contact with rain water, ice and snow from the gutters. If your gutters have been displaced or if a shingle tears, the soffit will rot out over time. Atlanta painting contractors often specialize in solving this external problem for you, thus preventing more serious damage to the interior as well.
To replace the rotted soffit, you would need to pry off the shingle mold running along the top edge of the fascia board and yank out all the nails that held the rotting board in place. Next, replace the board with a pre-measured or trimmed piece of hardwood, vinyl or aluminum. Remove any decorative trim beneath the soffit and remove the rotted soffit. Note that this part of the process is usually rather disgusting, since you never know what kind of dirt, dust, bee nest, squirrel nest, or debris will come off. Now you should be able to see the frame clearly and ascertain where the water damage and decay started. You may need to rip out additional plywood sheathing and use your saw to take out the section of rotted rafter or roofing. You'll have to cut four or more inches from the decay, to account for stress fractures that may have left room for water to seep in. This is where the tools come in handy: you'll need a powder-actuated nail gun with a .22 caliber blank to nail in the new section.
You'll also be attaching a pressure-treated 1x4 or 1x6 onto the newly sawed rafter, fastening it with 2.5" galvanized screws going from the new into the old rafters. Now you can cut a new soffit from a 3/8-inch A/C plywood, first coating the front and back flat surfaces with an exterior primer and the edges with a wax emulsion sealer (like AnchorSeal) to protect from water damage. Apply sealer with a foam or bristle brush. Nail the soffit into place and replace the trim you've removed. Cut a new fascia board and replace it. (Warning: This requires careful measuring to get the right size!) Now prime all four surfaces of this board. Seal the end cuts and install it, then nail up the shingle molds along the fascia.
Sound like a LOT of work? IT IS! The process is extremely convoluted for anyone who isn't a skilled tradesman. What might take a novice several days could be done in an afternoon by an Marietta Georgia painting contractor. Therefore, you may want to track down a contractor to meet your needs. Not only will your home look totally renovated and newer, but more importantly, you will be protecting your home from premature aging as a result of water and rot damage.
SHARE
